bellett.net
https://bellett.net/forums/

DOHC webber manifolds
https://bellett.net/forums/viewtopic.php?f=36&t=2726		 Page 1 of 1
Author:  F3ARED [ Wed May 28, 2014 12:48 am ]
Post subject:  DOHC webber manifolds
Hi guys,

Have so far somewhat unsuccessfully tried to get photos of DOHC webber manifolds as per the ones that are being made through the forum. Is anyone able to assist with some pictures so i can set about seeing if they are suitable for my ITB conversion?

Nick.
Author:  flying [ Thu May 29, 2014 9:40 am ]
Post subject:  Re: DOHC webber manifolds
Hi Nick

Found this website in Japan that sells the manifolds

I will post the link for the twin can manifold which is on page 4 but if you look on page 3 it would appear that the g161 twin webers manifolds -- no sure

http://www.microsofttranslator.com/bv.a ... 26page%3D2

Cheers Flying
Author:  flying [ Thu May 29, 2014 9:41 am ]
Post subject:  Re: DOHC webber manifolds
Nick

link is to page 3 look at page 4

OOPS
Author:  BULLITT [ Thu May 29, 2014 10:13 am ]
Post subject:  Re: DOHC webber manifolds
so 30.000 yen is approx. $320 aus
Author:  Glenn [ Thu May 29, 2014 11:27 pm ]
Post subject:  Re: DOHC webber manifolds
BULLITT wrote:
so 30.000 yen is approx. $320 aus
Plus freight. Doesn't seem to bad a price. I wonder if they actually would ship here?
I have a 2L DOHC efi. Not sure what i am going to do with it now, but Webers are tempting !
Author:  F3ARED [ Fri May 30, 2014 12:14 am ]
Post subject:  Re: DOHC webber manifolds
flying wrote:
Hi Nick

Found this website in Japan that sells the manifolds

I will post the link for the twin can manifold which is on page 4 but if you look on page 3 it would appear that the g161 twin webers manifolds -- no sure

http://www.microsofttranslator.com/bv.a ... 26page%3D2

Cheers Flying


Yeah I found those ones yesterday via Import Monster, unfortunately due to the design they are I cant use them as I have nowhere to mount the injector :(

Glenn, jump on Import Monster, they act as the middle man between buying from Japan and sending to Aus.
Author:  Glenn [ Fri May 30, 2014 1:15 am ]
Post subject:  Re: DOHC webber manifolds
F3ARED wrote:
flying wrote:
Hi Nick

Found this website in Japan that sells the manifolds

I will post the link for the twin can manifold which is on page 4 but if you look on page 3 it would appear that the g161 twin webers manifolds -- no sure

http://www.microsofttranslator.com/bv.a ... 26page%3D2

Cheers Flying


Yeah I found those ones yesterday via Import Monster, unfortunately due to the design they are I cant use them as I have nowhere to mount the injector :(

Glenn, jump on Import Monster, they act as the middle man between buying from Japan and sending to Aus.


I'm not ready to do anything right now. But good to know they are there.
Author:  flying [ Thu Jun 05, 2014 3:12 am ]
Post subject:  Re: DOHC webber manifolds
Nick

If you have to back to basics

http://www.ebay.com.au/itm/2-x-Weber-DC ... 621wt_1128

Cheers
Flying
Author:  Glenn [ Thu Jun 05, 2014 3:37 am ]
Post subject:  Re: DOHC webber manifolds
flying wrote:
Nick

If you have to back to basics

http://www.ebay.com.au/itm/2-x-Weber-DC ... 621wt_1128

Cheers
Flying


It might be cheaper to have them laser cut here in Oz? Especially if a few were made. You still need the other side anyway, to make a manifold so getting both made locally for a DOHC would be the go. Then find an alloy welder to weld in the tubes between them ?
Not as 'nice' as cast ones but usable i would imagine.
Page 1 of 1 All times are UTC
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/